Basic migration of the CEA user server address space JCL (CEAPROC) - optional

Below is an example of the CEA user server JCL. The changes required are highlighted in bold:

//CEAPROC  PROC P1=TRACE,P2=TAURSERV,P3=CEAPROC
//CEAPROC  EXEC PGM=IKJEFT01,DYNAMNBR=175,
//             PARM='%CEALOGON &P1 &P2 &P3',TIME=120
//TAURHLQ  SET  TAURHLQ=HLQ.ZSERVER
//TCPDATA  SET  TCPDATA=TCPIP.TCPDATA
//******************************************************************** 
//* Z/SERVER 
//********************************************************************* 
//STEPLIB  DD  DISP=SHR,DSN=&TAURHLQ..LOADLIB
//IPCONFIG DD DISP=SHR,DSN=&TAURHLQ..CONFIG(IVPCEAU)
//SYSTCPD  DD  DISP=SHR,DSN=&TCPDATA
//CEEREX30 DD SYSOUT=* 
//SYSPRINT DD SYSOUT=* 
//CEATSPRT DD SYSOUT=* 
//ZCOTSPRT DD TERM=TS 
//ZCOTSIN  DD TERM=TS 
//READER   DD  SYSOUT=(*,INTRDR) 
//MAINTASK DD SYSOUT=* 
//T0000001 DD SYSOUT=* 
//CMDTASK  DD SYSOUT=* 
//SRVTASK  DD SYSOUT=* 
//CEATASK  DD SYSOUT=* 
//CEAISPF  DD SYSOUT=* 
//LISTENER DD  SYSOUT=* 
//********************************************************************* 
//*      ADD YOUR OWN LOGON PROCEDURE HERE 
//*      BUT KEEP ALL &TAURHLQ DATA SETS IN THE RIGHT PLACES 
//********************************************************************* 
//SYSUADS  DD  DISP=SHR,DSN=SYS1.UADS 
//SYSLBC   DD  DISP=SHR,DSN=SYS1.BRODCAST 
//SYSPROC  DD  DISP=SHR,DSN=ISP.SISPCLIB 
//         DD  DISP=SHR,DSN=SYS1.SBLSCLI0 
//SYSEXEC  DD  DISP=SHR,DSN=&TAURHLQ..EXEC 
//         DD  DISP=SHR,DSN=&TAURHLQ..REXX 
//         DD  DISP=SHR,DSN=ISP.SISPEXEC 
//SYSHELP  DD  DISP=SHR,DSN=SYS1.HELP 
//         DD  DISP=SHR,DSN=ISP.SISPHELP 
//ISPMLIB  DD  DISP=SHR,DSN=ISP.SISPMENU 
//         DD  DISP=SHR,DSN=SYS1.SBLSMSG0 
//         DD  DISP=SHR,DSN=ISF.SISFMLIB 
//         DD  DISP=SHR,DSN=&TAURHLQ..MSGS 
//ISPEXEC  DD  DISP=SHR,DSN=ISP.SISPEXEC 
//ISPLLIB  DD  DISP=SHR,DSN=&TAURHLQ..LOADLIB 
//ISPPLIB  DD  DISP=SHR,DSN=ISP.SISPPENU 
//         DD  DISP=SHR,DSN=&TAURHLQ..PANELS 
//         DD  DISP=SHR,DSN=SYS1.SBLSPNL0 
//         DD  DISP=SHR,DSN=ISF.SISFPLIB 
//ISPSLIB  DD  DISP=SHR,DSN=&TAURHLQ..SKELS 
//         DD  DISP=SHR,DSN=ISP.SISPSLIB 
//         DD  DISP=SHR,DSN=ISP.SISPSENU 
//         DD  DISP=SHR,DSN=ISF.SISFSLIB 
//         DD  DISP=SHR,DSN=SYS1.SBLSKEL0 
//ISPTLIB  DD  DISP=SHR,DSN=ISP.SISPTENU 
//         DD  DISP=SHR,DSN=SYS1.SBLSTBL0 
//         DD  DISP=SHR,DSN=ISF.SISFTLIB 
//         DD  DISP=SHR,DSN=SYS1.SMP.OTABLES 
//ISPCTL1  DD  DISP=NEW,UNIT=SYSALLDA,SPACE=(CYL,(1,1)), 
//             DCB=(LRECL=80,BLKSIZE=800,RECFM=FB) 
//ISPCTL2  DD  DISP=NEW,UNIT=SYSALLDA,SPACE=(CYL,(1,1)), 
//             DCB=(LRECL=80,BLKSIZE=800,RECFM=FB) 
//ISPLST1  DD  DISP=NEW,UNIT=SYSALLDA,SPACE=(CYL,(1,1)), 
//             DCB=(LRECL=121,BLKSIZE=1210,RECFM=FBA) 
//ISPLST2  DD  DISP=NEW,UNIT=SYSALLDA,SPACE=(CYL,(1,1)), 
//             DCB=(LRECL=121,BLKSIZE=1210,RECFM=FBA) 
//SDSFMENU DD  DSN=ISF.SISFPLIB,DISP=SHR 
//ISPTABL  DD  DSN=SYS1.SMP.OTABLES,DISP=SHR
//         PEND

The CEAPROC procedure statement has been added and now defines three new parameters, which are used in the CEAPROC EXEC statement:

• P1 specifies if tracing should be enabled whilst reading the XML configuration file. Do not change this unless asked to do so by a member of Micro Focus SupportLine staff.
• P2 is the DSP_TOKEN that the CEA user server should use. This must match the DSP_TOKEN specified in the XML configuration file.
• P3 is an internal parameter that the CEA user server uses. This must match the CEA_LOGONPROC of the CEA user server.

The TCPDATA is used by the SYSTCPD DD statement to specify the TCPIP settings for use in the LE environment.

There is also an additional final PEND statement.